aboutsummaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
authorArnaud Ebalard <arno@natisbad.org>2014-11-22 00:46:57 +0100
committerJason Cooper <jason@lakedaemon.net>2014-11-22 04:44:25 +0000
commit389c74aaace1ae2a423184b03d8198311fef2c7d (patch)
tree9124f57a38fbed59b52949296124037fc8fc7e88
parent0e76f78cb3924050e969439eff6d5cc7685deb2b (diff)
arm: mvebu: add .dts file for Synology DS414
Synology DS414 is a 4-bay NAS powered by a Marvell Armada XP (mv78230 dual-core @1.33Ghz). It is very similar on many aspects to previous 4-bay synology models based on Marvell kirkwood SoC. Here is a short summary of the device: - 1GB RAM - Boot on SPI flash (64Mbit Micron N25Q064) - 2 GbE interfaces (Armada MAC connected to two Marvell 88E1512 PHY via RGMII) - 1 front USB 2.0 ports (directly handled by the Armada 370) - 2 rear USB 3.0 ports (handled by an EtronTech EJ168A XHCI controller on the PCIe bus) - 4 internal SATA ports handled by a Marvell 88SX7042 SATA-II controller on the PCIe bus) - Seiko S-35390A I2C RTC chip - UART0 providing serial console - UART1 used for poweroff (connected to a Microchip PIC16F883) Additional note: the front LEDs the and the two fans are not directly connected to the SoC and under its control. The former are presumably driven by the SATA controller, the latter by the PIC. [ jac: fixed up s/ge[01]_rgmii_pins/pmx_ge[01]_rgmii/ to match armada-xp.dtsi ] Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Arnaud Ebalard <arno@natisbad.org> Link: https://lkml.kernel.org/r/5b678d6d1f2f42f4bf0d087878b9d8024d463ea7.1416613429.git.arno@natisbad.org Signed-off-by: Jason Cooper <jason@lakedaemon.net>
-rw-r--r--arch/arm/boot/dts/Makefile3
-rw-r--r--arch/arm/boot/dts/armada-xp-synology-ds414.dts330
2 files changed, 332 insertions, 1 deletions
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index cfcf400..88346b3 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -510,7 +510,8 @@ dtb-$(CONFIG_MACH_ARMADA_XP) += \
armada-xp-lenovo-ix4-300d.dtb \
armada-xp-matrix.dtb \
armada-xp-netgear-rn2120.dtb \
- armada-xp-openblocks-ax3-4.dtb
+ armada-xp-openblocks-ax3-4.dtb \
+ armada-xp-synology-ds414.dtb
dtb-$(CONFIG_MACH_DOVE) += dove-cm-a510.dtb \
dove-cubox.dtb \
dove-cubox-es.dtb \
diff --git a/arch/arm/boot/dts/armada-xp-synology-ds414.dts b/arch/arm/boot/dts/armada-xp-synology-ds414.dts
new file mode 100644
index 0000000..ba5e94d
--- /dev/null
+++ b/arch/arm/boot/dts/armada-xp-synology-ds414.dts
@@ -0,0 +1,330 @@
+/*
+ * Device Tree file for Synology DS414
+ *
+ * Copyright (C) 2014, Arnaud EBALARD <arno@natisbad.org>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the old 0xd0000000).
+ * The 0xf1000000 is the default used by the recent, DT-capable, U-Boot
+ * bootloaders provided by Marvell. It is used in recent versions of
+ * DSM software provided by Synology. Nonetheless, some earlier boards
+ * were delivered with an older version of u-boot that left internal
+ * registers mapped at 0xd0000000. If you have such a device you will
+ * not be able to directly boot a kernel based on this Device Tree. In
+ * that case, the preferred solution is to update your bootloader (e.g.
+ * by upgrading to latest version of DSM, or building a new one and
+ * installing it from u-boot prompt) or adjust the Devive Tree
+ * (s/0xf1000000/0xd0000000/ in 'ranges' below).
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-xp-mv78230.dtsi"
+
+/ {
+ model = "Synology DS414";
+ compatible = "synology,ds414", "marvell,armadaxp-mv78230",
+ "marvell,armadaxp", "marvell,armada-370-xp";
+
+ chosen {
+ bootargs = "console=ttyS0,115200 earlyprintk";
+ stdout-path = &uart0;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x00000000 0 0x40000000>; /* 1GB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>;
+
+ pcie-controller {
+ status = "okay";
+
+ /*
+ * Connected to Marvell 88SX7042 SATA-II controller
+ * handling the four disks.
+ */
+ pcie@1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+
+ /*
+ * Connected to EtronTech EJ168A XHCI controller
+ * providing the two rear USB 3.0 ports.
+ */
+ pcie@5,0 {
+ /* Port 1, Lane 0 */
+ status = "okay";
+ };
+ };
+
+ internal-regs {
+
+ /* RTC is provided by Seiko S-35390A below */
+ rtc@10300 {
+ status = "disabled";
+ };
+
+ spi0: spi@10600 {
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q064";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <20000000>;
+
+ /*
+ * Warning!
+ *
+ * Synology u-boot uses its compiled-in environment
+ * and it seems Synology did not care to change u-boot
+ * default configuration in order to allow saving a
+ * modified environment at a sensible location. So,
+ * if you do a 'saveenv' under u-boot, your modified
+ * environment will be saved at 1MB after the start
+ * of the flash, i.e. in the middle of the uImage.
+ * For that reason, it is strongly advised not to
+ * change the default environment, unless you know
+ * what you are doing.
+ */
+ partition@00000000 { /* u-boot */
+ label = "RedBoot";
+ reg = <0x00000000 0x000d0000>; /* 832KB */
+ };
+
+ partition@000c0000 { /* uImage */
+ label = "zImage";
+ reg = <0x000d0000 0x002d0000>; /* 2880KB */
+ };
+
+ partition@003a0000 { /* uInitramfs */
+ label = "rd.gz";
+ reg = <0x003a0000 0x00430000>; /* 4250KB */
+ };
+
+ partition@007d0000 { /* MAC address and serial number */
+ label = "vendor";
+ reg = <0x007d0000 0x00010000>; /* 64KB */
+ };
+
+ partition@007e0000 {
+ label = "RedBoot config";
+ reg = <0x007e0000 0x00010000>; /* 64KB */
+ };
+
+ partition@007f0000 {
+ label = "FIS directory";
+ reg = <0x007f0000 0x00010000>; /* 64KB */
+ };
+ };
+ };
+
+ i2c@11000 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ s35390a: s35390a@30 {
+ compatible = "sii,s35390a";
+ reg = <0x30>;
+ };
+ };
+
+ /* Connected to a header on device's PCB. This
+ * provides the main console for the device.
+ *
+ * Warning: the device may not boot with a 3.3V
+ * USB-serial converter connected when the power
+ * button is pressed. The converter needs to be
+ * connected a few seconds after pressing the
+ * power button. This is possibly due to UART0_TXD
+ * pin being sampled at reset (bit 0 of SAR).
+ */
+ serial@12000 {
+ status = "okay";
+ };
+
+ /* Connected to a Microchip PIC16F883 for power control */
+ serial@12100 {
+ status = "okay";
+ };
+
+ poweroff@12100 {
+ compatible = "synology,power-off";
+ reg = <0x12100 0x100>;
+ clocks = <&coreclk 0>;
+ };
+
+ /* Front USB 2.0 port */
+ usb@50000 {
+ status = "okay";
+ };
+
+ mdio {
+ phy0: ethernet-phy@0 { /* Marvell 88E1512 */
+ reg = <0>;
+ };
+
+ phy1: ethernet-phy@1 { /* Marvell 88E1512 */
+ reg = <1>;
+ };
+ };
+
+ ethernet@70000 {
+ status = "okay";
+ pinctrl-0 = <&pmx_ge0_rgmii>;
+ pinctrl-names = "default";
+ phy = <&phy1>;
+ phy-mode = "rgmii-id";
+ };
+
+ ethernet@74000 {
+ pinctrl-0 = <&pmx_ge1_rgmii>;
+ pinctrl-names = "default";
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+ };
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&sata1_pwr_pin &sata2_pwr_pin
+ &sata3_pwr_pin &sata4_pwr_pin>;
+ pinctrl-names = "default";
+
+ sata1_regulator: sata1-regulator {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "SATA1 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ startup-delay-us = <2000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+ };
+
+ sata2_regulator: sata2-regulator {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "SATA2 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ startup-delay-us = <4000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+ };
+
+ sata3_regulator: sata3-regulator {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "SATA3 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ startup-delay-us = <6000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+ };
+
+ sata4_regulator: sata4-regulator {
+ compatible = "regulator-fixed";
+ reg = <4>;
+ regulator-name = "SATA4 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ startup-delay-us = <8000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&pinctrl {
+ sata1_pwr_pin: sata1-pwr-pin {
+ marvell,pins = "mpp42";
+ marvell,function = "gpio";
+ };
+
+ sata2_pwr_pin: sata2-pwr-pin {
+ marvell,pins = "mpp44";
+ marvell,function = "gpio";
+ };
+
+ sata3_pwr_pin: sata3-pwr-pin {
+ marvell,pins = "mpp45";
+ marvell,function = "gpio";
+ };
+
+ sata4_pwr_pin: sata4-pwr-pin {
+ marvell,pins = "mpp46";
+ marvell,function = "gpio";
+ };
+
+ sata1_pres_pin: sata1-pres-pin {
+ marvell,pins = "mpp34";
+ marvell,function = "gpio";
+ };
+
+ sata2_pres_pin: sata2-pres-pin {
+ marvell,pins = "mpp35";
+ marvell,function = "gpio";
+ };
+
+ sata3_pres_pin: sata3-pres-pin {
+ marvell,pins = "mpp40";
+ marvell,function = "gpio";
+ };
+
+ sata4_pres_pin: sata4-pres-pin {
+ marvell,pins = "mpp41";
+ marvell,function = "gpio";
+ };
+
+ syno_id_bit0_pin: syno-id-bit0-pin {
+ marvell,pins = "mpp26";
+ marvell,function = "gpio";
+ };
+
+ pmx_syno_id_bit1: syno-id-bit1-pin {
+ marvell,pins = "mpp28";
+ marvell,function = "gpio";
+ };
+
+ pmx_syno_id_bit2: syno-id-bit2-pin {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+
+ pmx_fan1_alarm: fan1-alarm-pin {
+ marvell,pins = "mpp33";
+ marvell,function = "gpio";
+ };
+
+ fan2_alarm_pin: fan2-alarm-pin {
+ marvell,pins = "mpp32";
+ marvell,function = "gpio";
+ };
+};